To use Bio Cleanze or Lightning Cleanze? – that is the question ...

January 05, 2016 2 Comments

To use Benz Bio Cleanze or Benz Lightning Cleanze? – that is the question ...

 

We've noticed a lot of confusion on the various forums about which softwash products to use, when to use them, and how power washing fits into the soft washing big picture. ~In this post we do our best to clarify the situation.

We've conducted multiple long-term tests in which we observed the effect of various combinations of Benz Bio Cleanze, Benz Lightning Cleanze, and pressure/power/jet washing. What follows in this article are our suggestions for best practices, arrived at through our hands-on observations and experience.


Watch the short video below to understand the basics
Note that the video refers to the old names of Benz Lightning Cleanze ("Blackwash") and Benz Bio Cleanze ("Biocidal Wash")


The different characteristics of our softwash biocides

Bio Cleanze is the strongest and most cost-effective quaternary ammonium ("quat") DDAC biocide in the UK and Ireland. It has a residual biocidal effect because it requires contact with organic matter to break down. Therefore some of the active ingredient is able to remain and kill spores that land on the surface in the months following treatment.

The combination of warm weather and high rainfall facillitates the rapid spread of algae. This is true especially of horizontal surfaces such as paths and drives. But on surfaces treated with Bio Cleanze we have noticed no sign of algae growth returning even after 12-24 months, which shows how powerful the residual biocidal effect is.

This affect can be seen most noticeably on surfaces that have been pre-cleaned using either Lightning Cleanze or a power washer as there is less organic matter to break down the active ingredient (DDAC). 

Lightning Cleanze is a powerful formula combining a sophisticated surfactant, a pleasant scent, and high quality sodium hypochlorite. It does not have a residual biocidal effect (neither does any sodium hypochlorite based product) because the sodium hypochlorite breaks down within 30-60 minutes of application. It does not require contact with organic matter to break down, although contact speeds up that process.

Lightning Cleanze is the first treatment of choice for all surfaces that should not be power-washed – such as soft sandstone, limestone and render – which have been contaminated with heavy organic growth. Then follow up with a post-treatment of Bio Cleanze.

Treating surfaces with a softwash biocide

On vertical surfaces that do not accumulate damp, treatment with Lightning Cleanze may be sufficient for a while. Then a treatment with Bio Cleanze 12 months later, followed by ongoing bi-annual treatments with Bio Cleanze will keep most walls perpetually clean.

Quick tip: For walls in damp, shaded areas, an annual treatment with Bio Cleanze may be necessary.

Horizontal surfaces suffer from damp much more than walls, and so the potential for re-contamination is much greater. Concrete paths, patios, and drives come up well with Lightning Cleanze and benefit from an annual post-treatment with Bio Cleanze to offer permanent residual biocidal protection.

Quick tip: We recommend Bio Cleanze for tarmac as our experience is that this leaves the tarmac looking good and deals with most biological growths within 24-48 hours.

Some infestations are harder to shift than others. For example, the black lichen that can grow on concrete paths and patios can be a really tough proposition to remove. The choice of which method to use depends upon the severity of the contamination, the likelihood of re-contamination, and on whether or not you have access to a power washer.

We've used this example of treating black lichen on concrete paths and patios to illustrate the possible combinations of approach that soft washing offers:

1) Light power wash followed by Bio Cleanze (works well and provides residual biocidal effect)

2) Lightning Cleanze > Light power wash & rinse > Lightning Cleanze > Rinse (works well on severe contamination and although it has no residual biocidal effect this method reduces the materials cost)

3) Lightning Cleanze (1-2 applications) > Light power wash & rinse > Bio Cleanze (loosens up and removes severe growths prior to power washing, then offers residual biocidal protection)

4) Lightning Cleanze (1-3 applications) > Bio Cleanze (when a power washer is not available)


Dilution rates: If the contamination is not too severe, and on most non-porous surfaces, Lightning Cleanze @ 10:1 may be sufficient but for severe contamination use 5:1.

Bio Cleanze can be used to great effect at 50:1 and also as strong as 20:1. Do not apply to surfaces that will be walked on by children or animals at a strength greater than 50:1 and allow the surface to dry completely before they are allowed access.

Quick tip: Two successive treatments at 50:1 can be more effective than a single treatment at 25:1 because this allows for the active ingredient to have a longer contact time with, and a deeper penetration into, the biological growth.

You'll find from experience what combination and which dilution rate works best for specific situations and surfaces. We cannot give absolute figures and recommendations because the climatic variables of temperature, wind, sunlight, rainfall, shading, and composition of the surface being treated all vary from region to region and from job to job.

The experience needed to calculate these variables makes soft washing a skilled profession, which makes it both interesting and justifies your fees.


Quick tip: Whenever you apply Bio Cleanze following Lightning Cleanze always thoroughly rinse the surface to ensure as much of the Lightning Cleanze surfactant as possible is removed. And we suggest allowing a full 60 minutes for the sodium hypochlorite in Lightning Cleanze to completely break down before treating the surface with Bio Cleanze.

 

Important information about softwash surfactants

There are thousands of amine surfactants and not all are biodegradable. And some will break down sodium hypochlorite even before it reaches the surface to be cleaned.


The surfactant we use in Lightning Cleanze is highly specialised, biodegradable, and was developed by our industrial chemists specifically for use in Lightning Cleanze. The use of this high quality surfactant ensures Lightning Cleanze remains stable and does not break down the sodium hypochlorite before it reaches the surface to cleaned.

Combined with the highest quality sodium hypochlorite in Lightning Cleanze (beware cheap hypo products as all hypo is not created equal – they vary in strength, purity, and conformity with REACH regulations) means this is a very high quality product. Comparing Lightning Cleanze with cheap hypo, cheap surfactant, and cheap scent is like comparing a new BMW with an old banger.

 

Rinsing technique following Lightning Cleanze treatment: It's important to rinse Lightning Cleanze from the surface 30-60 minutes following application. Also to rinse between treatments if the surface requires more than one application. The fastest and most effective rinsing method is to use a power washer at low pressure, using a rinsing nozzle (a hosepipe will do but is less effective).

If you don't have a machine with adjustable pressure, use a fan jet held well away from the surface to reduce the pressure on the surface (to tap water pressure) and so as not to cause damage.

 

When to use Bio Cleanze:

  • Soft washing roofs.
  • Following power washing.
  • Following a treatment with Lightning Cleanze.
  • Soft washing tarmac.
  • Rendered walls that are stained red or green.
  • Historic buildings where care of the structure is highly important.


Examples of when to use Lightning Cleanze:

  • Vertical surfaces such as rendered walls, if stained black.
  • Surfaces contaminated by black stains and lichen, including concrete patios, paths, and drives.
  • Soft surfaces that would be damaged by power washing, such as sandstone, limestone, and render.
  • Historic buildings where care of the structure is highly important.
  • When your customer demands the fastest possible results.

 

 Examples of when to use a power washer:

  • Cobblelock paths and drives to clear out the weeds, followed by Bio Cleanze.
  • Heavy lichen infestation in concrete paths and patios, in conjunction with Lightning Cleanze, Tornado Cleanze and Bio Cleanze.
  • Rinsing both horizontal and vertical surfaces, using a rinse nozzle or fan jet (keep pressure on the surface low by turning pressure down to tap water pressure. or keeping a fan jet well away from the surface)


We hope this information is helpful and sincerely wish you great success in your soft washing business,

Ben, Leo, Fiona, Stevie & Anthony

 

Click here to explore the full range of Benz softwash cleaning products

Benz Softwash Bio Cleanze DDAC biocide & Benz Softwash Lightning Cleanze SH sodium hypochlorite biocide

2 Responses

Leo
Leo

March 17, 2016

Hi Tim

1) If you have pressure washed a drive and it is clean, then we recommed post-treating with Biocidal Wash at 40:1 (winter) and 50:1 (summer) to provide residual biocide protection. There is nothing to be gained by treating an already clean surface with Blackwash or any other SH product.

2) Hosing down paths and patios is a good idea if there is a lot of mud and organic growth. It’s a simple form of pre-cleaning that will allow the chemical to work more effectively. Brush away all puddles and ideally allow the surface to dry as much as possible before treating with Blackwash so the surface water does not further dilute the chemical.

But if the paths are clean then you can apply Blackwash to a dry surface, usually at 5:1.

I hope this helps.

Wishing you soft washing success!

Leo

Tim Ogburn
Tim Ogburn

March 08, 2016

Hi
i have two questions please….1) When pressure washed a block drive i used to use 5 to 1 SH is blackwash ok to use at same dilution or should i be opting for 10.1

2) when using black wash on concerete paths is it ideal to hose area then apply blackwash or is it ok as the above question
Many thanks
Tim

Leave a comment

Comments will be approved before showing up.


Also in Benz Trade Tips

How to use Benz Tornado Cleanze to treat lichen on through-colour wall render
How to use Benz Tornado Cleanze to treat lichen stains on wall render

October 13, 2021

Lichen stains on render can be troublesome to remove. In this video Ben demonstrates how to quickly and easily use Benz Tornado Cleanze to remove lichen staining from through-colour render.

Click the link on this page to watch the video ... (and we'd love to read your comments and questions, so feel free to leave them in the Comment section under the vid on YouTube)

View full article →

How to quickly and effectively clean pebble dash with Lightning Cleanze
How to quickly and effectively clean pebble dash with Benz Lightning Cleanze

September 25, 2021 2 Comments

Watch the Benz team demonstrate how to quickly and effectively clean pebble dash wall render with Benz Lightning Cleanze. This type of render  cannot be pressure washed because the pebbles will be dislodged from the surface. Soft washing is the solution and in this video we show you how ...

Click the link on this page to watch the video

View full article →

How to safely soft wash asbestos roof slates, tiles & sheeting
How to safely soft wash asbestos roof slates, tiles & sheeting

September 15, 2021

Many soft wash contractors can be unsure of the safest way to soft wash asbestos roofs. So in this post we lay out the best practices we've learned from running a soft washing business since 2013.

Click the link on this page to learn how to treat asbestos ...

View full article →